As specified in §63.5805, you must meet the following organic HAP emissions limits that apply to you:
| If your operation type is . . . | And you use . . . | 1Your organic HAP emissions limit is . . . |
|---|---|---|
| 1. open molding—corrosion-resistant and/or high strength (CR/HS) | a. mechanical resin application b. filament application c. manual resin application |
113 lb/ton. 171 lb/ton. 123 lb/ton. |
| 2. open molding—non-CR/HS | a. mechanical resin application b. filament application c. manual resin application |
88 lb/ton. 188 lb/ton. 87 lb/ton. |
| 3. open molding—tooling | a. mechanical resin application b. manual resin application |
254 lb/ton. 157 lb/ton. |
| 4. open molding—low-flame spread/low-smoke products | a. mechanical resin application b. filament application c. manual resin application |
497 lb/ton. 270 lb/ton. 238 lb/ton. |
| 5. open molding—shrinkage controlled resins2 | a. mechanical resin application b. filament application c. manual resin application |
354 lb/ton. 215 lb/ton. 180 lb/ton. |
| 6. open molding—gel coat3 | a. tooling gel coating b. white/off white pigmented gel coating c. all other pigmented gel coating d. CR/HS or high performance gel coat e. fire retardant gel coat f. clear production gel coat |
440 lb/ton. 267 lb/ton. 377 lb/ton. 605 lb/ton. 854 lb/ton. 522 lb/ton. |
| 7. centrifugal casting—CR/HS | a. resin application with the mold closed, and the mold is vented during spinning and cure b. resin application with the mold closed, and the mold is not vented during spinning and cure c. resin application with the mold open, and the mold is vented during spinning and cure d. resin application with the mold open, and the mold is not vented during spinning and cure |
25 lb/ton.4 NA—this is considered to be a closed molding operation. 25 lb/ton.4 Use the appropriate open molding emission limit.5 |
| 8. centrifugal casting—non-CR/HS | a. resin application with the mold closed, and the mold is vented during spinning and cure b. resin application with the mold closed, and mold is not vented during the spinning and cure c. resin application with the mold open, and the mold is vented during spinning and cure d. resin application with the mold open, and the mold is not vented during spinning and cure |
20 lb/ton.4 NA—this is considered to be a closed molding operation. 20 lb/ton.4 Use the appropriate open molding emission limit.5 |
| 9. pultrusion6 | N/A | reduce total organic HAP emissions by at least 60 weight percent. |
| 10. continuous lamination/casting | N/A | reduce total organic HAP emissions by at least 58.5 weight percent or not exceed an organic HAP emissions limit of 15.7 lbs of organic HAP per ton of neat resin plus and neat gel coat plus. |
1Organic HAP emissions limits for open molding and centrifugal casting are expressed as lb/ton. You must be at or below these values based on a 12-month rolling average.
2This emission limit applies regardless of whether the shrinkage controlled resin is used as a production resin or a tooling resin.
3If you only apply gel coat with manual application, for compliance purposes treat the gel coat as if it were applied using atomized spray guns to determine both emission limits and emission factors. If you use multiple application methods and any portion of a specific gel coat is applied using nonatomized spray, you may use the nonatomized spray gel coat equation to calculate an emission factor for the manually applied portion of that gel coat. Otherwise, use the atomized spray gel coat application equation to calculate emission factors.
4For compliance purposes, calculate your emission factor using only the appropriate centrifugal casting equation in item 2 of Table 1 to this subpart, or a site specific emission factor for after the mold is closed as discussed in §63.5796.
5Calculate your emission factor using the appropriate open molding covered cure emission factor in item 1 of Table 1 to this subpart, or a site specific emission factor as discussed in §63.5796.
6Pultrusion machines that produce parts that meet the following criteria: 1,000 or more reinforcements or the glass equivalent of 1,000 ends of 113 yield roving or more; and have a cross sectional area of 60 square inches or more are not subject to this requirement. Their requirement is the work practice of air flow management which is described in Table 4 to this subpart.
[70 FR 50131, Aug. 25, 2005]
Tried the LawStack mobile app?
Join thousands and try LawStack mobile for FREE today.
- Carry the law offline, wherever you go.
- Download CFR, USC, rules, and state law to your mobile device.
