40 CFR Table 6
Emission Limitations for Energy Recovery Units That Commenced Construction After June 4, 2010, or That Commenced Reconstruction or Modification After August 7, 2013
June 9, 2020
CFR
Open Table
For the air pollutant You must meet this emission limitation1 Using this averaging time2 And determining compliance
using this method2
Liquid/gas Solids
Cadmium 0.023 milligrams per dry standard cubic meter Biomass-0.0014 milligrams per dry standard cubic meter
Coal-0.0017 milligrams per dry standard cubic meter
3-run average (collect a minimum volume of 4 dry standard cubic meters per run) Performance test (Method 29 at 40 CFR part 60, appendix A-8). Use ICPMS for the analytical finish.
Carbon monoxide 35 parts per million dry volume Biomass-240 parts per million dry volume
Coal-95 parts per million dry volume
3-run average (1 hour minimum sample time per run) Performance test (Method 10 at 40 CFR part 60, appendix A-4).
Dioxin/furans (Total Mass Basis) No Total Mass Basis limit, must meet the toxic equivalency basis limit below Biomass-0.52 nanograms per dry standard cubic meter
Coal-5.1 nanograms per dry standard cubic meter
3-run average (collect a minimum volume of 4 dry standard cubic meters) Performance test (Method 23 at 40 CFR part 60, appendix A-7).
Dioxins/furans (toxic equivalency basis) 0.093 nanograms per dry standard cubic meter Biomass-0.076 nanograms per dry standard cubic meter3
Coal-0.075 nanograms per dry standard cubic meter
3-run average (collect a minimum volume of 4 dry standard cubic meters per run) Performance test (Method 23 of appendix A-7 of this part).
Fugitive ash Visible emissions for no more than 5 percent of the hourly observation period Three 1-hour observation periods Visible emission test (Method 22 at 40 CFR part 60, appendix A-7) Fugitive ash.
Hydrogen chloride 14 parts per million dry volume Biomass-0.20 parts per million dry volume
Coal-58 parts per million dry volume
3-run average (For Method 26, collect a minimum volume of 360 liters per run. For Method 26A, collect a minimum volume of 3 dry standard cubic meters per run) Performance test (Method 26 or 26A at 40 CFR part 60, appendix A-8).
Lead 0.096 milligrams per dry standard cubic meter Biomass-0.014 milligrams per dry standard cubic meter
Coal-0.057 milligrams per dry standard cubic meter
3-run average (collect a minimum volume of 4 dry standard cubic meters per run) Performance test (Method 29 at 40 CFR part 60, appendix A-8). Use ICPMS for the analytical finish.
Mercury 0.00056 milligrams per dry standard cubic meter Biomass-0.0022 milligrams per dry standard cubic meter
Coal-0.013 milligrams per dry standard cubic meter
3-run average (collect enough volume to meet an in-stack detection limit data quality objective of 0.03 ug/dscm) Performance test (Method 29 or 30B at 40 CFR part 60, appendix A-8) or ASTM D6784-02 (Reapproved 2008).3
Nitrogen oxides 76 parts per million dry volume Biomass-290 parts per million dry volume
Coal-460 parts per million dry volume
3-run average (for Method 7E, 1 hour minimum sample time per run) Performance test (Method 7 or 7E at 40 CFR part 60, appendix A-4).
Particulate matter (filterable) 110 milligrams per dry standard cubic meter Biomass-5.1 milligrams per dry standard cubic meter
Coal-130 milligrams per dry standard cubic meter
3-run average (collect a minimum volume of 1 dry standard cubic meter per run) Performance test (Method 5 or 29 at 40 CFR part 60, appendix A-3 or appendix A-8) if the unit has an annual average heat input rate less than 250 MMBtu/hr; or PM CPMS (as specified in §60.2145(x)) if the unit has an annual average heat input rate equal to or greater than 250 MMBtu/hr.
Sulfur dioxide 720 parts per million dry volume Biomass-7.3 parts per million dry volume
Coal-850 parts per million dry volume
3-run average (for Method 6, collect a minimum of 60 liters, for Method 6C,1 hour minimum sample time per run) Performance test (Method 6 or 6C at 40 CFR part 60, appendix A-4).

1All emission limitations are measured at 7 percent oxygen, dry basis at standard conditions. For dioxins/furans, you must meet either the Total Mass Basis limit or the toxic equivalency basis limit.

2In lieu of performance testing, you may use a CEMS or, for mercury, an integrated sorbent trap monitoring system to demonstrate initial and continuing compliance with an emissions limit, as long as you comply with the CEMS or integrated sorbent trap monitoring system requirements applicable to the specific pollutant in §§60.2145 and 60.2165. As prescribed in §60.2145(u), if you use a CEMS or an integrated sorbent trap monitoring system to demonstrate compliance with an emissions limit, your averaging time is a 30-day rolling average of 1-hour arithmetic average emission concentrations.

3Incorporated by reference, see §60.17.


Tried the LawStack mobile app?

Join thousands and try LawStack mobile for FREE today.

  • Carry the law offline, wherever you go.
  • Download CFR, USC, rules, and state law to your mobile device.