(a)
(1) "bus" means a motor vehicle with motive power (except a trailer) designed to carry more than 10 individuals.
(2) "multipurpose passenger vehicle" means a motor vehicle with motive power (except a trailer), designed to carry not more than 10 individuals, that is constructed either on a truck chassis or with special features for occasional off-road operation.
(3) "passenger car" means a motor vehicle with motive power (except a multipurpose passenger vehicle, motorcycle, or trailer) designed to carry not more than 10 individuals.
(4) "truck" means a motor vehicle with motive power (except a trailer) designed primarily to transport property or special purpose equipment.
(b)
(A) 95 percent of each manufacturer's annual production of passenger cars manufactured after August 31, 1996, and before September 1, 1997.
(B) 80 percent of each manufacturer's annual production of buses, multipurpose passenger vehicles, and trucks (except walk-in van-type trucks and vehicles designed to be sold only to the United States Postal Service) with a gross vehicle weight rating of not more than 8,500 pounds and an unloaded vehicle weight of not more than 5,500 pounds manufactured after August 31, 1997, and before September 1, 1998.
(C) 100 percent of each manufacturer's annual production of passenger cars manufactured after August 31, 1997.
(D) 100 percent of each manufacturer's annual production of vehicles described in clause (B) of this paragraph manufactured after August 31, 1998.
(2) Manufacturers may not use credits and incentives available before September 1, 1998, under the provisions of Standard 208 (as amended by this section) to comply with the requirements of paragraph (1)(D) of this subsection after August 31, 1998.
(c)
(1) either or both of the front outboard seating positions of the vehicle are equipped with an inflatable restraint referred to as an "airbag" and a lap and shoulder belt;
(2) the "airbag" is a supplemental restraint and is not a substitute for lap and shoulder belts;
(3) lap and shoulder belts also must be used correctly by an occupant in a front outboard seating position to provide restraint or protection from frontal crashes as well as other types of crashes or accidents; and
(4) occupants should always wear their lap and shoulder belts, if available, or other safety belts, whether or not there is an inflatable restraint.
(d)
(e)
(2) The Secretary of Transportation may grant an exemption under paragraph (1) of this subsection if the Secretary finds that there has been a disruption in the supply of any component of an inflatable restraint or in the use and installation of that component by the manufacturer because of an unavoidable event not under the control of the manufacturer that will prevent the manufacturer from meeting its anticipated production volume of vehicles with those restraints.
(3) Only an affected manufacturer may apply for an exemption. The Secretary of Transportation shall prescribe in the amendment to Standard 208 required under this section the information an affected manufacturer must include in its application under this subsection. The manufacturer shall specify in the application the models, lines, and types of vehicles affected. The Secretary may consolidate similar applications from different manufacturers.
(4) An exemption or renewal of an exemption is conditioned on the commitment of the manufacturer to recall the exempted vehicles for installation of the omitted inflatable restraints within a reasonable time that the manufacturer proposes and the Secretary of Transportation approves after the components become available in sufficient quantities to satisfy both anticipated production and recall volume requirements.
(5) The Secretary of Transportation shall publish in the Federal Register a notice of each application under this subsection and each decision to grant or deny a temporary exemption and the reasons for the decision.
(6) The Secretary of Transportation shall require a label for each exempted vehicle that can be removed only after recall and installation of the required inflatable restraint. The Secretary shall require that written notice of the exemption be provided to the dealer and the first purchaser of each exempted vehicle other than for resale, with the notice being provided in a way, and containing the information, the Secretary considers appropriate.
(f)
(A) affecting another provision of law carried out by the Secretary of Transportation applicable to passenger cars, buses, multipurpose passenger vehicles, or trucks; or
(B) establishing a precedent related to developing or prescribing a Government motor vehicle safety standard.
(2) This section and amendments to Standard 208 made under this section may not be construed as indicating an intention by Congress to affect any liability of a motor vehicle manufacturer under applicable law related to vehicles with or without inflatable restraints.
(g)
(A) a combination of inflated restraints and lap and shoulder belts;
(B) inflated restraints only; and
(C) lap and shoulder belts only.
(2) In consultation with the Secretaries of Labor and Defense, the Secretary of Transportation also shall provide information and analysis on lap and shoulder belt use, nationally and in each State by—
(A) military personnel;
(B) Government, State, and local law enforcement officers;
(C) other Government and State employees; and
(D) the public.
(h)
(1) after September 30, 1994, for use by the Government be equipped, to the maximum extent practicable, with driver-side inflatable restraints; and
(2) after September 30, 1996, for use by the Government be equipped, to the maximum extent practicable, with inflatable restraints for both front outboard seating positions.
Open Table
Revised Section |
Source (U.S. Code) | Source (Statutes at Large) |
---|---|---|
30127(a) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2502(a), 105 Stat. 2081. |
30127(b) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2508(a)(1) (1st sentence), (b), 105 Stat. 2084, 2085. |
30127(c) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2508(a)(2), 105 Stat. 2085. |
30127(d) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2508(a)(3), 105 Stat. 2085. |
30127(e) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2508(c), 105 Stat. 2086. |
30127(f) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2508(a)(1) (last sentence), (d), 105 Stat. 2085, 2086. |
30127(g) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2508(e), 105 Stat. 2086. |
30127(h) | 15:1392 (note). | Dec. 18, 1991, Pub. L. 102–240, §2508(f), 105 Stat. 2087. |
In subsection (a), the definitions are derived from section 2502(a) of the Intermodal Surface Transportation Efficiency Act of 1991 (Public Law 102–240, 105 Stat. 2081) and are restated because those definitions apply to the source provisions being restated in this section.
In subsection (b)(1), before clause (A), the words "Notwithstanding any other provision of law or rule" and "(to the extent such Act is not in conflict with the provisions of this section)" are omitted as unnecessary because of the restatement. The words "The amendment shall require" are substituted for "The amendment promulgated under subsection (a) shall establish the following schedule" for clarity. The words "manufactured on or after the dates specified in the applicable schedule established by subsection (b)", "The amendment shall take effect", and "Subject to the provisions of subsection (c)" are omitted as unnecessary because of the restatement. The words "for both of the front outboard seating positions for each" are substituted for "for the front outboard designated seating positions of each" for clarity. In clause (B), the word "new" is omitted as unnecessary because of the restatement. The word "only" is substituted for "exclusively" for consistency in the revised title.
In subsection (b)(2), the words "after August 31, 1998" are substituted for "on and after such date" for clarity.
In subsection (c), before clause (1), the words "In amending Standard 208, the Secretary of Transportation shall require" are substituted for "The amendment to such Standard 208 shall also require" for clarity and to eliminate unnecessary words.
In subsection (e)(3), the words "Only an affected manufacturer may apply for an exemption" are added for clarity. The words "consolidate similar applications from different manufacturers" are substituted for "consolidate applications of a similar nature of 1 or more manufacturers" for clarity.
In subsection (f)(1), before clause (A), the words "by the Secretary or any other person, including any court" are omitted as surplus. In clause (A), the word "affecting" is substituted for "altering or affecting" to eliminate an unnecessary word.
In subsection (f)(2), the words "by any person or court" are omitted as unnecessary. The word "affect" is substituted for "affect, change, or modify" to eliminate unnecessary words.
In subsection (g)(1), before clause (A), the words "and every 6 months after that date through" are substituted for "biannually . . . and continuing to" for clarity. The word "actual" is omitted as unnecessary. The word "expressed" is substituted for "defined" for clarity.
In subsection (g)(2)(C), the words "other Government and State employees" are substituted for "Federal and State employees other than law enforcement officers" for clarity and because of the restatement.
In subsection (h)(2), the words "for both front outboard seating positions" are substituted for "for both the driver and front seat outboard seating positions" for clarity and consistency in this section.
References in Text
The National Traffic and Motor Vehicle Safety Act of 1966, referred to in subsec. (b)(1), is Pub. L. 89–563, Sept. 9, 1966, 80 Stat. 718, as amended, which was classified generally to chapter 38 (§1381 et seq.) of Title 15, Commerce and Trade, and was substantially repealed by Pub. L. 103–272, §7(b), July 5, 1994, 108 Stat. 1379, and reenacted by the first section thereof as this chapter.
Amendments
1998—Subsec. (g)(1). Pub. L. 105–178 substituted "annually" for "every 6 months" in introductory provisions.
Improvement of Data Collection on Child Occupants in Vehicle Crashes
Pub. L. 114–94, div. B, title XXIV, §24407, Dec. 4, 2015, 129 Stat. 1726, provided that:
"(a)
"(1) The type or types of child restraint systems in use during the crash in any vehicle involved in the crash, including whether a five-point harness or belt-positioning booster. [sic]
"(2) If a five-point harness child restraint system was in use during the crash, whether the child restraint system was forward-facing or rear-facing in the vehicle concerned.
"(b)
"(c)
Child Safety Seats
Pub. L. 112–141, div. C, title I, §31501, July 6, 2012, 126 Stat. 773, provided that:
"(a)
"(b)
"(1)
"(2)
Child Restraint Anchorage Systems
Pub. L. 112–141, div. C, title I, §31502, July 6, 2012, 126 Stat. 774, provided that:
"(a)
"(b)
"(1)
"(2)
"(A) the Committee on Commerce, Science, and Transportation of the Senate; and
"(B) the Committee on Energy and Commerce of the House of Representatives."
Rear Seat Belt Reminders
Pub. L. 112–141, div. C, title I, §31503, July 6, 2012, 126 Stat. 774, provided that:
"(a)
"(b)
"(1)
"(2)
"(A) the Committee on Commerce, Science, and Transportation of the Senate; and
"(B) the Committee on Energy and Commerce of the House of Representatives."
New Deadline
Pub. L. 112–141, div. C, title I, §31505, July 6, 2012, 126 Stat. 775, provided that: "If the Secretary [of Transportation] determines that any deadline for issuing a final rule under this Act [probably should be "this title", see Tables for classification] cannot be met, the Secretary shall—
"(1) provide the Committee on Commerce, Science, and Transportation of the Senate and the Committee on Energy and Commerce of the House of Representatives with an explanation for why such deadline cannot be met; and
"(2) establish a new deadline for that rule."
Improving the Safety of Child Restraints
Pub. L. 107–318, Dec. 4, 2002, 116 Stat. 2772, provided that:
"SECTION 1. SHORT TITLE.
"This Act may be cited as 'Anton's Law'.
"SEC. 2. FINDINGS.
"Congress finds the following:
"(1) It is the policy of the Department of Transportation that all child occupants of motor vehicles, regardless of seating position, be appropriately restrained in order to reduce the incidence of injuries and fatalities resulting from motor vehicle crashes on the streets, roads, and highways.
"(2) Research has shown that very few children between the ages of 4 to 8 years old are in the appropriate restraint for their age when riding in passenger motor vehicles.
"(3) Children who have outgrown their child safety seats should ride in a belt-positioning booster seat until an adult seat belt fits properly.
"(4) Children who were properly restrained when riding in passenger motor vehicles suffered less severe injuries from accidents than children not properly restrained.
"SEC. 3. IMPROVEMENT OF SAFETY OF CHILD RESTRAINTS IN PASSENGER MOTOR VEHICLES.
"(a)
"(b)
"(1) consider whether to include injury performance criteria for child restraints, including booster seats and other products for use in passenger motor vehicles for the restraint of children weighing more than 50 pounds, under the requirements established in the rulemaking proceeding;
"(2) consider whether to establish performance requirements for seat belt fit when used with booster seats and other belt guidance devices;
"(3) consider whether to address situations where children weighing more than 50 pounds only have access to seating positions with lap belts, such as allowing tethered child restraints for such children; and
"(4) review the definition of the term 'booster seat' in Federal motor vehicle safety standard No. 213 under section 571.213 of title 49, Code of Federal Regulations, to determine if it is sufficiently comprehensive.
"(c)
"SEC. 4. DEVELOPMENT OF ANTHROPOMORPHIC TEST DEVICE SIMULATING A 10-YEAR OLD CHILD.
"(a)
"(b)
"SEC. 5. REQUIREMENTS FOR INSTALLATION OF LAP AND SHOULDER BELTS.
"(a)
"(1) require a lap and shoulder belt assembly for each rear designated seating position in a passenger motor vehicle with a gross vehicle weight rating of 10,000 pounds or less, except that if the Secretary determines that installation of a lap and shoulder belt assembly is not practicable for a particular designated seating position in a particular type of passenger motor vehicle, the Secretary may exclude the designated seating position from the requirement; and
"(2) apply that requirement to passenger motor vehicles in phases in accordance with subsection (b).
"(b)
"SEC. 6. EVALUATION OF INTEGRATED CHILD SAFETY SYSTEMS.
"(a)
"(1) the safety of the child restraint and correctness of fit for the child;
"(2) the availability of testing data on the system and vehicle in which the child restraint will be used;
"(3) the compatibility of the child restraint with different makes and models;
"(4) the cost-effectiveness of mass production of the child restraint for consumers;
"(5) the ease of use and relative availability of the child restraint to children riding in motor vehicles; and
"(6) the benefits of built-in seats for improving compliance with State child occupant restraint laws.
"(b)
"SEC. 7. DEFINITIONS.
"As used in this Act, the following definitions apply:
"(1)
"(2)
"(3)
"SEC. 8. AUTHORIZATION OF APPROPRIATIONS.
"(a)
"(1) the evaluation required by section 6 of this Act; and
"(2) research of the nature and causes of injury to children involved in motor vehicle crashes.
"(b)
Pub. L. 106–414, §14, Nov. 1, 2000, 114 Stat. 1806, provided that:
"(a)
"(b)
"(1) whether to require more comprehensive tests for child restraints than the current Federal motor vehicle safety standards requires, including the use of dynamic tests that—
"(A) replicate an array of crash conditions, such as side-impact crashes and rear-impact crashes; and
"(B) reflect the designs of passenger motor vehicles as of the date of the enactment of this Act [Nov. 1, 2000];
"(2) whether to require the use of anthropomorphic test devices that—
"(A) represent a greater range of sizes of children including the need to require the use of an anthropomorphic test device that is representative of a ten-year-old child; and
"(B) are Hybrid III anthropomorphic test devices;
"(3) whether to require improved protection from head injuries in side-impact and rear-impact crashes;
"(4) how to provide consumer information on the physical compatibility of child restraints and vehicle seats on a model-by-model basis;
"(5) whether to prescribe clearer and simpler labels and instructions required to be placed on child restraints;
"(6) whether to amend Federal Motor Vehicle Safety Standard No. 213 (49 CFR 571.213) to cover restraints for children weighing up to 80 pounds;
"(7) whether to establish booster seat performance and structural integrity requirements to be dynamically tested in 3-point lap and shoulder belts;
"(8) whether to apply scaled injury criteria performance levels, including neck injury, developed for Federal Motor Vehicle Safety Standard No. 208 to child restraints and booster seats covered by in Federal Motor Vehicle Safety Standard No. 213; and
"(9) whether to include child restraint in each vehicle crash tested under the New Car Assessment Program.
"(c)
"(d)
"(e)
"(f)
"(g)
"(h)
"(i)
Improving Air Bag Safety
Pub. L. 105–178, title VII, §7103, June 9, 1998, 112 Stat. 465, provided that:
"(a)
"(1)
"(2)
"(3)
"(4)
"(5)
"(A) so certified in advance of the phase-in period; or
"(B) in excess of the percentage requirements during the phase-in period.
"(b)