of altitude to 5 feet. 2Percent of full range. 3For airplanes that can demonstrate the capability of deriving either the control input on control movement (one from the other) for all modes of operation and flight regimes, the “or” applies. For airplanes with non-mechanical control systems (fly-by-wire) the “and” applies. In airplanes with split surfaces, suitable

of altitude to 5 feet. 2Per cent of full range. 3For airplanes that can demonstrate the capability of deriving either the control input on control movement (one from the other) for all modes of operation and flight regimes, the “or” applies. For airplanes with non-mechanical control systems (fly-by-wire) the “and” applies. In airplanes with split surfaces, suitable

intermittent driving difficulty. Degree B Commuting Conditions Roads typically fair but may be good for part of distance or may be unpaved for short distances; climatic conditions during part of a season, in relation to terrain, contribute to additional cost. Degree C Commuting Conditions Fair to poor roads; unpaved for part of distance, or travel over range; hilly or mountainous terrain

with a thermal protection or an insulation system used for the transportation of a Class 2 (compressed gas) material must have at least the upper two-thirds of the exterior of the tank, including manway nozzle and all appurtenances in contact with this area, finished with a reflective coat of white paint. 5For inside diameter of 87 inches or less, the thickness of plates shall be not less than

Pub. L. 95–473, Oct. 17, 1978, 92 Stat. 1439, related to temporary operating approval for transactions involving motor and water carriers. See section 14303 of this title. Section 11350,

(a) The area comprising that portion of the land and waters located in the towns of Provincetown, Truro, Wellfleet, Eastham, Orleans, and Chatham in the Commonwealth of Massachusetts, and described in subsection (b), is designated for establishment as Cape Cod National Seashore (hereinafter referred to as "the seashore"). (b) The area referred to in subsection (a) is described as follows:

paragraph (a) of this section except for the following: (1) An attending vessel as defined in § 147.20; and (2) A vessel authorized by the First Coast Guard District Commander or a designated representative. (d)

part 1910, which have been identified as also applicable to construction work. This republication developed a single set of OSHA regulations for both labor and management forces within the construction industry. 2. Nomenclature changes to part 1926 appear at 84 FR 21597, May 14, 2019.

part 1910, which have been identified as also applicable to construction work. This republication developed a single set of OSHA regulations for both labor and management forces within the construction industry. 2. Nomenclature changes to part 1926 appear at 84 FR 21597, May 14, 2019.

with, and published as part of, the contents of the volume for the next regular session. The United States Statutes at Large shall be legal evidence of laws, concurrent resolutions, treaties, international agreements other than treaties, proclamations by the President, and proposed or ratified amendments to the Constitution of the United States therein contained, in all the courts of the United States, the several States, and the Territories and insular possessions of the United States.

compliance dates for sources subject to subpart DD. 63.6(b)(2) No 63.6(b)(3) No 63.6(b)(4) No

Table 1 to Subpart HH of Part 63—List of Hazardous Air Pollutants for Subpart HH Open Table CAS Numbera

Yes 63.1(b)(3) No §63.1400(e) provides documentation requirements for APPUs not considered affected sources. 63.1(c)(1)

§63.1315 for certain continuous process vents and with §63.1321 for all batch process vents. The owner or operator of an affected source producing PET using a batch process or producing polystyrene using a batch process shall comply with §63.1315 for continuous process vents and with

Except definition of major source is unique for this source category and there are additional definitions in subpart HHH. §63.3(a) through (c) Yes.

5 U.S.C. 102. (3) An agency or court of the judicial branch, including a court as defined in 28 U.S.C. 610, the District Court for the Northern Mariana Islands, and the Judicial Panel on Multidistrict Litigation; (4) An agency of the legislative branch, including the U.S. Senate and the U.S. House of Representatives; and

(a) VA will not collect a debt involving benefits under the laws administered by VA by salary offset unless the Secretary or appropriate designee first provides the employee with a minimum of 30 calendar days written notice. (b) If the employee has not previously appealed the amount or existence of the debt under 38 CFR parts 19 and 20 and the time for pursuing such an appeal has not expired (

temperature, and humidity control or simulation which meets the requirements of §86.161-00 for running emission tests with the air conditioning operating. Federal Test Procedure, or FTP means the test procedure as described in §86.130-00 (a) through (d) and (f) which is designed to measure urban driving tail pipe exhaust emissions and

(a) The efficiency of the converter used for the conversion of NO2 to NO is tested as given in paragraphs (a)(1) through (a)(8) of this section. (1) Using the test setup as shown in Figure 1 in Appendix B of this subpart (see also §90.318 of this chapter) and the procedure described

(a) The efficiency of the converter used for the conversion of NO2 to NO is tested as given in paragraphs (a)(1) through (a)(8) of this section (see Figure 2 in appendix B to this subpart). (1) Using the test setup as shown in Figure 2 in appendix B to this subpart (see also §91.318

eligibility for repair under the remedial plan and a description of the proof to be required of a locomotive or locomotive engine owner to demonstrate compliance with such condition. Eligibility may not be denied solely on the basis that the locomotive or locomotive engine owner used parts not manufactured or remanufactured by the manufacturer or remanufacturer, or had repairs not performed by the manufacturer or remanufacturer. (4) A clear description of the components

than as a means of transportation such as when used as an energy or mining facility, a storage facility or a seafood processing facility, or when secured to a storage facility or a seafood processing facility, or when secured to the bed of the ocean, contiguous zone or waters of the United States for the purpose of mineral or oil exploration or development. (b) Discharges of dredged or fill material into waters of the United States which are regulated under section

(a) The owner or operator must develop and follow a schedule and procedure for inspecting overfill controls. (b) The owner or operator must inspect at least once each operating day data gathered from monitoring and leak detection equipment (e.g., pressure or temperature gauges, monitoring wells) to ensure that the tank system is being operated according to its design.